Статья: Physical Methods of Speed-Independent Module Design

Physical Methods of Speed-Independent Module Design

Oleg Izosimov

INTEC Ltd, Room 321, 7a Myagi Street, Samara 443093, Russia

1. Introduction

Any method of logic circuit design is based on using formal models of gates

and wires. The simplest model of a gate is determined by only two

"parameters": (a) Boolean function is to be calculated, (b) fixed propagation

delay. The simplest model of a wire is an ideal medium with zero resistance

and consequently, with zero delay. Such simple models allow circuit design

procedures which are a sequence of elementary steps easily realized by a

computer.

When logic circuits designed by using the simplest models expose unreliable

operation as in the case of gate delay variations, designers introduce less

convenient but more realistic models with arbitrary but finite delay. Using

more complicated models may produce logic circuits that are called speed-

independent [1].

In speed-independent circuits transition duration can be arbitrary. So a

centralized clock cannot be used. Instead special circuitry to detect output

validity is applied. Besides, additional interface circuitry is needed to

communicate with the environment in a handshaking manner. A speed-independent

circuit can be seen as a module consisting of combinational logic (CL)

proper, CL output validity detector (OVD) and interface circuitry (Fig.1). To

enable OVD to distinguish valid output data from invalid ones, the redundant

coding scheme was proposed [2]. The main idea of the scheme is to enumerate

all possible input and output data, both valid and invalid. The OVD must be

provided with appropriate information on data validity. To realize the idea

of redundant coding some constraints on CL design are imposed [3]:

(i) CL must be free of delay hazards, i.e. CL output data word must not be

dependent on the relative delay of signal paths through CL.

(ii) In changing between input states, any intermediate or transient states

that are passed through must not be mapped by CL onto valid output states.

When these constraints were formulated, the circuit designers realised that

not every Boolean description could be implemented in a speed-independent

style. Other approaches to speed-independent module design were needed.

SIM design as a science has two branches: logical and physical. For a long

time physical branch was overshadowed in spite of its competitiveness. The

main properties of physical approach to SIM design are:

(a) Arbitrary coding scheme.

(b) Conventional procedure of operational unit design.

(c) Races of signals in SIM do not affect on its proper operation.

In this paper we propose an approach based on the physical nature of

transitions in CL. We believe that each transition is actually a transfer of

energy which can be naturally detected by physical methods.

From the viewpoint of a radio engineer CL behaves like a radio transmitter. It

emits radio frequencies in the 108-1010Hz band modulated

by signals of 106-108Hz. Obviously, the carrier wave is

produced by gate switchings during transitions in CL. The modulating wave is

produced by control schemes (OVD and interface circuitry) that detect

transition completion and inform the environment about the readiness of CL. OVD

is a kind of radio receiver that extracts the modulation envelope and enhances

the received signal. The main properties that OVD circuit must expose from a

radio engineer's point of view are selectivity and high gain. Since the useful

signals can propagate through non-conducting medium, OVD circuits can be

coupled with CL indirectly.

Advances in semiconductor technology gave birth to two methods of transition

detecting based on two kinds of the information carrying signal, namely

electromagnetic radiation and current consumption. Frequency of the signal

produced by switching logic gates is determined by gate delay.

For instance, CMOS network of 1-ns gates produces 1-GHz signal, ECL array of

100-ps gates gives 10-GHz radiation. Logic circuits consisting of 10-ps gates

will emit infra-red radiation. That signal could be easily detected by

photosensitive devices.

2. Background

Let us have a closer look at the structure of speed-independent modules (SIM)

as presented in Fig.1. All input data are processed in CL, all output data

are obtained from CL, too. So, CL is the only unit in SIM which is involved

in proper data processing. The result of that processing is specified by

Boolean functions. Algorithms for calculating the Boolean function are

realised by the internal structure of CL. Generally, its structure is series-

parallel as well as algorithm implemented.

When n-bit data word is put into the CL, n or more signal

propagation paths (SPPs) can be activated concurrently. So, one can say that

the calculation of a Boolean function by CL is of parallel nature. On the other

hand, each SPP is a gate chain which processes data in a serial manner. So,

calculation in CL is also of sequential nature.

The OVD circuit is intended for detecting transient and steady "states" of

CL. If any SPP in CL is still "active", CL is in transient state, otherwise

it is in steady state. Each gate switching results in both logical and

electromagnetic effects on its surrounding medium. The logical effects of

switching has been heavily investigated; we consider physical one.

To provide speed-independence of the module the OVD and interface circuitry

must also work in a speed-independent mode. This means that any arbitrary but

finite transistor or wire delay cannot impair proper operation of OVD and

interface circuitry.

The interface circuitry is a mediator between OVD and environment of SIM. It

implements any kind of signalling convention, commonly a two- or four-cycle one

[4] based on request Req and acknowledgement Ack signal using.

The interface circuitry receives the output validity (OV) signal from

the OVD circuit, a Req signal from the environment and transmits an

Ack signal to the environment (Fig.1).

Consider an algorithm of operation for interface circuitry realizing

speed-independent four-cycle signalling convention (FCSC). In accordance with

FCSC the control signals must go in the following sequence: Req+

OV-Ack+Req-Ack-

where "+" corresponds to rising the signal and "-" corresponds to falling the

signal. All signals are assumed to adhere to positive logic. Initially the

signals Req and Ack are low, the signal OV is high. If

the environment state changes, the Req signal rises and transient state

of CL occurs (OV-). Upon completion of the transitions in CL,

signal OV rises and the interface circuitry generates the Ack

signal rising. After that the environment produces a falling Req signal

and then the interface circuitry transmits the falling Ack signal to

the environment. All the signals have to be reset into the initial state.

To develop the interface circuitry a circuit designer must take into account

that any OVD circuit has finite (non-zero) turn-on delay ton

. This means that OVD cannot respond on transitions of short duration t

tr< ton .

An example of interface circuitry is shown in Fig.2. It contains a flip-flop,

a NOR-gate, an asymmetrical delay and an inverter as an output stage [5].

The asymmetrical delay is intended for delaying Req rising signal for

+ period where + > ton . Delaying

Req falling signal noted - is to be as short as possible. Note

that speed-independent operation of interface circuitry is vulnerable to delay

+ variation. If + becomes less than ton ,

proper operation of SIM can not be guaranteed. Otherwise, if + is

much more than ton , performance of SIM will be

significantly reduced. To provide exact accordance of + and t

on a circuit emulator can be used.

Such an emulator is either an exact copy of OVD or its functional copy, i.e.

resistive-capacitive model of OVD's critical path. In the chip the emulator

must be placed next to active OVD circuit in order to ensure identical

conditions of fabrication and operation.

In this example we use a simplified asymmetrical delay implemented as an

asymmetrical CMOS inverter chain (Fig.3). Contrary to the common inverter an

asymmetrical one has non-equal rise and fall times of output signal.

A time diagram for interface circuitry is presented in Fig.4 for two cases: (a)

ttr < ton and (b) ttr t

on. In case (a) the signal sequence Req+Ack

+ is formed for (++tNOR) period where t

NOR is a NOR-gate delay. In case (b) the above sequence is formed for

(ttr +toff+tNOR) duration

where toff is a turn-off delay of OVD circuit. When the SIM

returns to the initial steady state, the signal sequence Req-

Ack- is formed for (-+tNOR)

interval.

After considering the SIM in operation it is obvious that the main problems

of the module design are in the area of CL and OVD interaction. This includes

(a) kind of signal used as a carrier of information about CL output validity,

and (b) method of OVD circuit design.

4. Current consumption detection

Using current consumption of CMOS CL for output validity detection was proposed

in 1990 [7]. Contrary to the method of EMR detection this one is based on

introducing direct coupling of source and receiver. While CL is in steady state

it consumes current of about 10-9-10-8A which does not

allow OVD switching. The interface circuitry gets information on CL output

validity and in turn informs the environment about CL readiness to input data

processing. When an input data arrives CL changes its state to "transient",

current consumption increases to 10-4-10-2A, which

switches the OVD, thus informing the interface circuitry about output

invalidity. The latter lets the environment know about CL business.

After the computations in the CL are finished, the current consumption

decreases down to the steady state value, and the OVD sends a signal of

output validity.

4.1 Information carrying signal

Current consumption by CMOS CL contains useful information on CL state. CMOS

CL is a network of CMOS gates, so the current consumed by CL is a

superposition of currents consumed by CMOS gates included in the CL. Each

CMOS gate contains PMOS transistor and NMOS transistor networks (Fig.5).

While a gate is in a steady state either the PMOS or the NMOS network is in a

conducting mode. When a gate switches the non-conducting transistor network

becomes conducting. There is usually a short period in switching time when

both networks are in a conducting mode.

Generally, current consumed by a CMOS gate includes three components [9,10]:

(a) leakage current Ilk passing between power supply and

ground due to finite resistance of non-conducting transistor network;

(b) short-circuit current Isc flowing while both networks

are in a conducting mode;

(c) load capacitance CL charge current ILC

flowing while a CMOS gate is switching from low to high output voltage via

conducting PMOS network and CL .

SPICE simulation has shown [5] that amplitude of current consumed by a typical

CMOS inverter depends on CL and is limited by the non-zero

resistance of the conducting PMOS network (Fig.7). The integral of consumed

current is proportional to CL . When a gate switches from

high to low output voltage, the component ILC is negative by

direction and negligible by value (Fig.7b). It is evident, the switchings from

high to low output voltage occur at the expense of energy accumulated in C

L during the previous switching from low to high output voltage. The

component Isc does not depend on direction in which a gate

switches.

The component ILC equals to ILC = C

LVdd f where Vdd is a power supply

voltage, f is a gate switching frequency. Veendrick has investigated

the component Isc dependencies on CL and

rise-fall time of input potential signal [10]. He showed that if both input and

output signal have the same rise-fall time, the component Isc

cannot be more than 20 percent of summary current consumption [10]. However,

when the output signal rise-fall time is less than input one, the component

Isc can be of the same order of magnitude as ILC

. In that case it must be taken into account. As to the component Ilk

, it entirely depends on CMOS process parameters and for state of the art CMOS

devices Ilk is about 10-15 -10-12 A.

So, the analysis of CMOS gate current consumption allows us to conclude that in

transient state a CMOS gate consumes a current I= Ilk

+Isc+ILC and in steady state it consumes

only Ilk<< I . The difference between two

states from the viewpoint of current consumption is several orders of

magnitude. So, CMOS gate output validity detection is possible, both in

principle and in practice.

In Section 2 we presented series-parallel model of computations in CL. We

showed that in every moment during switching current consumed by CL is a

superposition of the currents consumed on the activated signal propagation

paths (SPPs). Now, considering CL implemented by CMOS devices we should note

that while logical signal propagates through SPP the neighbouring gates

switch in opposite directions. That is why a curve of current consumed by a

ten inverter chain (Fig.8) looks like a combination of crests and troughs.

Nevertheless, in the very lowest point of the curve the current consumed by

CL in a transient state remains several orders more than in a steady state.

4.2 OVD implementation

The proposed OVD circuit, shown in Fig.9, is a threshold circuit translating an

analog current signal I into a logical signal OV.

The OVD circuit contains a current-to-voltage converter (CVC) consisting of the

resistor R1 and the diode D1. The OVD

also contains a comparator implemented by the MOS transistors M1

-M7 and resistors R2,,,R

3 . CMOS CL consumes the current I and introduces a capacitance

Cin . The capacitance Cout represents the load

caused by the interface circuitry. A low potential output signal of OVD

corresponds to CL output validity. A high potential output signal corresponds

to CL output invalidity. So, OVD generates OV signal in negative logic

manner.

The transfer characteristics of CVC is determined by a system of three

equations:

where I is an input current of CVC, V is a voltage drop on the

CVC circuit, Ir is a current flowing through the resistor

R1, Id is a current passing through the diode

D1, I0 is a leakage current of the diode,

rb is a bulk resistance of the diode. Here

stands for kT/q where k is Boltzmann's constant, T

is absolute temperature, q is charge of an electron.

Equations (1)-(3) determine the functional connection F between input

current I and voltage drop V:

. Graphic solution of the system is shown in Fig.10.

CVC parameters to be calculated are R1 and rb

. Initial data for calculating R1 are the threshold voltage

drop Vth and corresponding threshold input current I

th . Value Ith is determined by minimal current

consumed by CMOS CL in transient state. Initial data for calculating r

b are maximal voltage drop Vmax and corresponding

maximal input current Imax. Value Imax is

determined by the maximal number of gates in CL switching simultaneously and

their load capacitances.

The comparator chosen is the CMOS ECL receiver proposed by Chappell et

al.[11]. The circuit includes a single differential amplifier stage with

built-in compensation for parameter variations, followed by a CMOS inverter.

The comparator has 100-mV worst-case sensitivity in 1-m technology. Detailed

static and dynamic analysis of the comparator circuit was given in [11].

The comparator compares input voltage signal Vin with

reference voltage Vref. If Vin <V

ref the comparator output signal equals to logical zero which means that

CL outputs are valid. Otherwise, Vin >Vref

, the comparator output signal equals to logical "one" which means that the

outputs are invalid.

As it follows from the OVD circuit configuration,

where Vdd is a voltage of power supply.

Equations (4) and (5) allow us to calculate the threshold voltage drop V

of the CVC circuit:

since , so

If 0<V<500mV then the diode D1 of CVC operates

in the very small current region Id 0 and Id

<<Ir. So the component Id in the

Equation (1) can be neglected and IIr =V/R

1 .

For practical values of

the threshold input current of the OVD circuit is reversely proportional to the

resistance of R1 :

. Substituting Equation (6) yields

.

As to choosing value of rb it must be done with regard to

maximal voltage drop Vmax .

If V>750mV, the diode D1 is in active mode and while r

b <<R1 the condition Ir

<<Id is true. So, in the large current region II

d and Equation (2) determines an almost linear dependence between

I and V. For instance, if the maximal voltage drop Vmax

=900mV and maximal input current Imax=2mA, then in accordance

with the Equation (2) rb 100. Typical element values for

the OVD circuit with Vth =400mV are given in Table 1.

The turn-on ton and turn-off toff delays

of the OVD circuit depend on the OVD itself and the CMOS CL as well. (Switching

the OVD output from low to high voltage is called "turning-on" and reverse

switching is called "turning-off".)

Consider a piece of CMOS CL and its interaction with OVD circuit (Fig.11). The

piece is an SPP including N logic gates. Each gate is shown

symbolically as a connection of PMOS and NMOS networks. All the capacitances

affecting ton and toff can be brought

down to three components:

(i) CLi is the load capacitance of the i-th gate;

(ii) Cpsi is the power supply bus capacitance associated with the i-th gate;

(iii) Cin is the input capacitance of the OVD circuit.

Let pi is a probability of the i-th gate being in the

state of high output potential. In this state the capacitance CLi

is connected with power supply bus through the low channel resistance of

turned-on transistors in PMOS network of the i-th gate. Then equivalent

capacitance Ceq connected to the OVD circuit input equals

(7)

where N is a number of gates in the considered SPP. Here the resistance

of conducting PMOS network is assumed to be negligible.

Equation (7) is also true for CL including several SPPs. In that case

summing must be carried out for all the gates belonging to CL.

Simulation shows that ton and toff are

proportional to the OVD time constant =R1Ceq.

It was also obtained that when N>20, the component under the sign of

summation in Equation (7) can be much larger than the component Cin

. Due to voltage drop V the effective power supply voltage is

reduced and CL performance is decreased by about 35 percent [7].

In order to make SIM operating faster special attention must be paid to

reducing the capacitance introduced by CL.

4.3 Speed-independent address bus

The simplest case of CL is a scheme degenerated into a set of wires called a

multi-bit bus. Let us develop the OVD circuit for such a CL.

Multi-bit bus consists of several lines. Each line can be considered as a

medium for signal propagating from one end of the chip to another. Delay

of signal propagation through a line depends on several factors:

(a) output impedance and symmetry of driver circuit;

(b) initial state of the line: if driver is symmetrical, line switching from

high to low voltage lasts shorter than reverse switching;

(c) electrical properties of the line as a signal propagation medium

(resistance of conducting layer and capacitances between the line and other

wires next to it);

(d) length of the line;

(e) input impedance and sensitivity of receiving circuit.

Since different lines of the bus operate in different conditions (a)-(e),

signal propagation delays are different, too. From the standpoint of

environment the bus behaves like any other more complicated CL.

Asynchronous RAM designers use a bus transition detector since 1980s [13-15].

Such a detector is usually based on double-rail address coding and two

series connected transistors for each address bit [15]. One of the

transistors receives the true address signal and the other receives the

complementary address signal of the particular address bit. For any steady

state condition one of the transistors will be turned on and one will be

turned off. There will be a finite rise and fall time during a transition of

the address bit. There is a short time during which both transistors are

conducting. The establishment of the conductive path provides the detection

of the address transition. In the first asynchronous RAMs the output

signal of the transition detector is used for bit line precharging and for

enabling/disabling sense amplifiers and peripheral circuitry.

Self-timed RAM announced in 1983 [14] used transition detectors not for

address transition only but also for detecting read/write completion and

address/bit line precharge completion as well.

The CMOS transition detector was invented in 1986 [15]. This circuit is also

based on double-rail coding and uses a pair of series-connected NMOS

transistors (Fig.12). The scheme for n-bit bus control contains n

line transition detectors (LTDs) and n AND-gates. Outputs of AND-gates

are united in node M forming wired OR. The output inverter serves as a

pulse shaper. Capacitors C1 and C2 are

intended to prolong rise time of the LTD output signal (true and

complementary). This is necessary for reliable detection.

The main drawback of the circuit is speed dependence. One can see that if

true and complementary address bit signal have different propagation delays,

the conducting path via NMOS transistors will never be formed.

Using the OVD circuit proposed in Section 4.2 as LTD we can avoid this drawback.

Note that address transmission through the address bus is unidirectional. So to

detect completion of bus transition it is enough to recognize the bus state at

the destination end. For this purpose we modify CL to consist of n

lines. The modification means introducing n LTDs, each actually a CMOS

inverter chain. Each chain contains two inverters loaded with a capacitance

(Fig.13). Input of each LTD is connected with corresponding line of the bus at

the destination end. Power supply pads of all LTDs are connected to the current

input of the same OVD circuit.

The parameters of the input current signal for the OVD circuit are varied by

(i) value of capacitances C1 and C2 ;

(ii) dimensions of MOS transistors M1 -M4 .

Since all transitions in CL are of the same duration and can be lengthened to

be outlast the OVD turning-on time, we simplify the interface circuitry by

disallowing the asymmetrical delay.

Due to short duration of normal transition in this CL we must take into

account the integral nature of the sensitivity of the OVD circuit. OVD

sensitivity depends on both amplitude and width of input current pulse.

Simulated operation region of the OVD circuit for current pulses shorter than

30ns is shown in Fig.14. It is obvious that in this case the threshold of the

OVD circuit must be determined by threshold charge Qth

value. The OVD input charge Q equals to

where I is OVD input current, t is a moment of time when

transition occurs, w is a width of input current pulse. Turning-on

condition for the OVD circuit is Q=Qth.

When the LTD circuit shown in Fig.13 is used, the charge value Q is

determined by either C1 or C2. Namely, if

the line goes from low to high voltage, Q=VC2. If the

line goes in the reverse direction then

where V is charging/discharging voltage, approximately equal to the

effective power supply voltage: VVdd -V. Here V

dd is OVD power supply voltage and V is CVC voltage drop.

The OVD circuit with typical parameters (See Table 1) has a threshold charge

value Qth =4.010-12 C. When C1

=C2 =CL , the minimal value of CL

providing OVD capacity for operation is about 1.010-12 F.

Influence of transistors M1 -M4 dimensions

on LTD delay d is determined by approximation [17]:

where ~ is a sign of proportionality, Gn and Gp

are the conductances of NMOS and PMOS transistors respectively (CL

=C1 =C2.)

Since and

where W and L are width and length of transistor channels of the

corresponding conduction type, the LTD delay d is proportional to

.

It has been obtained that for , , CL=1.0pF and Vdd-V=5.0V the LTD delay d=7.6ns.

When LTD works jointly with the OVD in the speed-independent bus, the real

value of the LTD delay will increase by 30-40 percent due to OVD's R

1 effect on the effective power supply voltage.

To determine the appropriate value of R1 in the OVD circuit

we must know threshold input current Ith corresponding to

threshold voltage drop Vth recommended to be equal to 400mV.

Average input current Iav in transient state of one line is

determined by the expression Iav =CLv

where v is the average rate of increase in the output signal for an

inverter included in LTD. For typical values v=1.0109 Volts

per second and CL =1.0pF, Iav =1.0mA.

Accepting Ith =0.4mA and Imax=2.0mA we

obtain R1=1k and rb=100.

Simulation has shown that in this case OVD turning-on delay can be

approximated by an empirical expression:

ton[ns]=8.1+0.1n

where n is the address bus bit capacity. Total delay of recognizing

address transition ttot =dg+ton

where g is a coefficient of the LTD delay increase due to reducing power

supply voltage. As we showed above g1.35. It can be seen that if n

=32, ttot=21.6ns.

4.4 Speed-independent adder

The circuit we use in this Section as a CL was a touch-stone for many speed-

independent circuit designers for about four decades. We mean a ripple carry

adder (RCA) which is actually a chain of one-bit full adders (Fig.14).

Each full adder calculates two Boolean functions: sum si=ai

bici and output carry ci+1

=aibi+bici+aici

where ai, bi are summands, ci

is input carry and stands for XOR operation.

In 1955 Gilchrist et al. proposed speed-independent RCA with carry completion

signal [18]. In 1960s that circuit was carefully analyzed and improved [19-

21]. In 1980 Seitz used RCA for illustrating his concept of equipotential

region and his approach to self-timed system design [4].

Now we use RCA as a CL for illustrating our approach to SIM design.

As it was shown in Section 4.2 the turn-on and turn-off delays of the OVD

circuit are proportional to the equivalent capacitance Ceq

associated with OVD circuit input. Capacitance Ceq depends

linearly on a number of gates N in CMOS CL. To speed up a SIM it is

necessary to reduce a number N. This can be reached by structural

decomposition CMOS CL into subcircuits CL1, CL2, etc. Each subcircuit CLi

is connected to its own detecting circuit OVDi or directly to the power

supply if this subcircuit transition does not affect the transition duration in

CL as a whole. Each detecting circuit OVDi generates its own OV

signal which is combined with other OVDs' output signals via a multi-input OR

(NOR) element. The output signal of that element serves as OV signal of

the CMOS CL.

Multi-bit RCA computation time is determined by length of maximal activated

carry chain. A lot of papers were devoted to analysis of carry generation and

carry propagation in RCA [19-21], many of them contained their own methods

for estimation or calculation of average maximal activated carry chain. We do

not intend to add another one.

Let us have a look inside RCA. As it was mentioned above RCA consists of one-bit

full adders and each full adder consists of two parts: forming sum s

i part and forming carry ci+1 part

(Fig.16).

In multi-bit RCA all forming sum parts do not interact with each other and do

not affect on transition duration in RCA. Each forming carry ci

+1 part receives ci signal from preceding forming carry

part and sends ci+1 signal to consequent one.

To decompose RCA we use three heuristic tricks:

(i) All forming sum parts we connect directly to power supply.

(ii) We divide each forming carry part into three subcircuits denoted in Fig.16

by numbers 1,2 and 3. All subcircuits 1 we connect directly to power supply

because they do not contain input ci and so do not contain

carry propagation path.

(iii) All subcircuits 2 we connect to OVD1 and all subcircuits 3 we connect to

OVD2. Outputs of OVD1 and OVD2 are connected to two-input NOR-gate forming

RCA OV signal in positive logic manner (Fig.17).

OVD1 and OVD2 input currents I1 and I2

curves for 6-bit RCA and longest transition duration are shown in Fig.18.

Accepting Vth1,2=400mV we calculated the OVD

circuits parameters. It was obtained R11=5k, Ith

1=0.08mA, R12=3k, Ith2

=0.13mA. OVD1 and OVD2 delay dependencies on a number of bits in RCA are shown

in Fig.19.

4.5 Comparison of SIMs with synchronous counterparts

Transition duration in CL is a random variable. Probability of transition with

duration D is determined by implemented Boolean function and

distribution of input logical combinations. Domain of possible values for

variable D occupies the interval [0;Dmax]. Here

Dmax is a length of critical path in CL.

Let is a

mathematical expectation of transition duration in CL where Di

is a length of i-th SPP in CL, pi is a probability

of i-th path being the longest activated SPP.

When CL works in the synchronous mode, the cycle duration Ts

is chosen with regard to maximal transition duration Dmax.

Certain margin must be added to Dmax to provide reliable

operation of CL in the case of CL parameter variations: Ts =

kDmax where k is a margin coefficient.

In SIM cycle duration is a random variable with expectation Tsi

= gDme+toff+tif where

g is a coefficient of CL delay increasing due to reducing power supply

voltage, toff is turn-off delay of the OVD circuit, t

if is an interface circuitry delay.

We determine efficiency E for speed-independent mode of CL operation as

relative increase of SIM performance in comparison to its synchronous

counterpart:.

Generally, speed-independent mode is more efficient than synchronous one if

Ts >Tsi or, in other words,

.

In the case of RCA

where tc is a delay of carry forming part, n is a

number of full adders in RCA.

It has been shown [19] that in n-bit RCA Dme tc

log2(5n/4). Then, in the case of speed-independent operation

Tsi=gtclog2(5n/4)+t

off+tif.

We have obtained dependencies of Ts , Tsi

on a number of bits in RCA that are shown in Fig.20. As it can be seen,

speed-independent operation of RCA is more efficient while n>8.

5.Conclusion

6.Acknowledgement

I would like to thank Igor Shagurin and Vlad Tsylyov of the Moscow Physical

Engineering Institute for helpful discussions of this work. I am also

grateful to Chris Jesshope of University of Surrey and Mark Josephs of Oxford

University who kindly provided the latest material on their research in the

area of delay-insensitive circuit design.

References

[1] Miller, R.E., Switching theory (Wiley, New York, 1965), vol.2,

Chapter 10.

[2] Unger, S.H., Asynchronous Sequential Switching Circuits (Wiley,

New York, 1969).

[3] Armstrong, D.B., A.D. Friedman, and P.R. Menon, Design of Asynchronous

Circuits Assuming Unbounded Gate Delays,

IEEE Trans.on Computers C-18 (12) (1969) 1110-1120.

[4] Seitz, C.L., System timing, in: C.A. Mead and L.A. Conway, eds.,

Introduction to VLSI Systems (Addison-Wesley, New

York, 1980), Chapter 7.

[5] Izosimov, O.A., I.I. Shagurin, and V.V. Tsylyov, Physical approach to CMOS

module self-timing, Electronics

Letters 26 (22) (1990) 1835-1836.

[6] Veendrick, H.J.M., Short-circuit dissipation of static CMOS circuit and

its impact on the design of buffer circuits, IEEE J.

Solid-State Circuits SC-19 (4) (1984) 468-473.

[7] Chappell, B.A, T.I. Chappell, S.E. Schuster, H.M. Segmuller, J.W.

Allan, R.L. Franch, and P.J. Restle, Fast CMOS ECL

receivers with 100-mV worst-case sensitivity, IEEE J. Solid-State

Circuits SC-23 (1) (1988) 59-67.

[8] Chu, S.T., J. Dikken, C.D. Hartgring, F.J. List, J.G. Raemaekers, S.A.

Bell, B. Walsh, and R.H.W. Salters, A 25-ns

Low-Power Full-CMOS 1-Mbit (128K8) SRAM, IEEE J. Solid-State

Circuits SC-23 (5) (1988) 1078-1084.

[9] Frank, E.H., and R.F. Sproull, A Self-Timed Static RAM, in: Proc.

Third Caltech VLSI Conference

(Springer-Verlag, Berlin, 1983) pp.275-285.

[10] Donoghue, W.J., and G.E. Noufer, Circuit for address transition

detection, US Patent 4563599, 1986.

[11] Huang, J.S.T., and J.W. Schrankler, Switching characteristics of scaled

CMOS circuits at 77K,

IEEE Trans. on Electron Devices ED-34 (1) (1987) 101-106.

[12] Gilchrist, B., J.H. Pomerene, and S.Y. Wong, Fast Carry Logic for Digital

Computers, IRE Trans. on Electronic Computers

EC-4 (4) (1955) 133-136.

[13] Hendrickson, H.C., Fast High-Accuracy Binary Parallel Addition,

IRE Trans. on Electronic Computers

EC-9 (4) (1960) 465-469.

[14] Majerski, S., and M. Wiweger, NOR-Gate Binary Adder with Carry

Completion Detection, IEEE Trans. on Electronic

Computers EC-16 (1) (1967) 90-92.

[15] Reitwiesner, G.W., The determination of carry propagation length for

binary addition, IRE Trans. on Electronic Computers

EC-9 (1) (1960) 35-38.

Appendix

SPICE2G.6: MOSFET model parameters

				VALUE
	Name	Parameter	Units	PMOS	NMOS
1	level	model index	-	3	3
2	VTO	ZERO-BIAS THRESHOLD VOLTAGE	V	-1.337	1.161
3	KP	TRANSCONDUCTANCE PARAMETER	A/V2	2.310-5	4.610-5
4	GAMMA	BULK THRESHOLD PARAMETER		0.501	0.354
5	PHI	SURFACE POTENTIAL	V	0.695	0.660
6	RD	DRAIN OHMIC RESISTANCE	OHM	333	85
7	RS	SOURCE OHMIC RESISTANCE	OHM	333	85
8	CBD	ZERO-BIAS B-D JUNCTION CAPACITANCE	F	1.9810-14	6.910-15
9	CBS	ZERO-BIAS B-S JUNCTION CAPACITANCE	F	1.9810-14	6.910-15
10	IS	BULK JUNCTION SATURATION CURRENT	A	3.4710-15	9.2210-15
11	PB	BULK JUNCTION POTENTIAL	V	0.8	0.8
12	CGSO	GATE-SOURCE OVERLAP CAPACI- TANCE PER METER CHANNEL WIDTH	F/M	6.7010-10	3.3010-10
13	CGDO	GATE-DRAIN OVERLAP CAPACI- TANCE PER METER CHANNEL WIDTH	F/M	6.7010-10	3.3010-10
14	CGBO	GATE-BULK OVERLAP CAPACITANCE PER METER CHANNEL LENGTH	F/M	1.9010-9	2.6010-9
15	RSH	DRAIN AND SOURCE DIFFUSION SHEET RESISTANCE	OHM/SQ	55	30
16	CJ	ZERO-BIAS BULK JUNCTION BOTTOM CAPACITANCE PER SQ METER OF JUNCTION AREA	F/M2	3.5310-4	1.2410-4
17	MJ	BULK JUNCTION BOTTOM GRADING COEFFICIENT	-	0.5	0.5
18	CJSW	ZERO-BIAS BULK JUNCTION SIDE- WALL CAPACITANCE PER METER OF JUNCTION PERIMETER	F/M	1.7110-10	3.2010-11